Fix a Leaky Faucet in Under an Hour
As an Amazon Associate, I earn from qualifying purchases.
That drip, drip, drip at 2 a.m. is more than annoying — it’s money going down the drain. According to the EPA’s WaterSense program, a faucet dripping just once per second wastes more than 3,000 gallons of water a year — the water for more than 180 showers — and on a metered water bill, you pay for every drop.
Here’s the good news: most faucet leaks are caused by a single worn part — a cartridge, a rubber washer, or a pair of seats and springs — and replacing it is a straightforward job for a first-time homeowner. If you can turn a wrench and follow steps in order, you can do this.
At a Glance
| Time | 30–60 minutes (most of it is the trip to the store) |
| Difficulty | Easy — a good first plumbing project |
| Parts cost | $5–$25 for most faucets |
| Pro cost if you give up | $100–$300 for a plumber visit |
| Tools needed | Adjustable wrench, Phillips and flathead screwdrivers, needle-nose pliers, Allen wrench set, plumber’s silicone grease, towel or rag |
Identify Your Faucet Type First
There are four faucet types in US homes, and the fix depends on which one you have. Spend two minutes on this before you buy anything — parts are brand- and type-specific, and the wrong part is a wasted trip.
| Type | How to spot it | Usual culprit |
|---|---|---|
| Compression | Two handles you twist several turns; common in homes built before the 1970s | Worn rubber washer |
| Ball | Single handle rotating over a dome-shaped cap; common in kitchens, mostly Delta | Worn seats and springs |
| Cartridge | Single or double handle with a removable cartridge inside; most common since the 1990s (Moen, Kohler) | Worn cartridge or O-ring |
| Ceramic disc | Single wide lever over a cylindrical body | Cracked disc or mineral buildup |
Step 1: Shut Off the Water
This is the one step you never skip. Never take a faucet apart with the water still on — the moment you pull a cartridge or stem out, you’ll have an uncontrolled spray inside your cabinet.
Look under the sink for the angle stop valves — the small oval-handled valves on the hot and cold supply lines. Turn both clockwise (“righty-tighty”) until they stop, then open the faucet handles to release the pressure and drain the lines. You’ll get a short burst, then nothing.
If there are no shutoff valves under the sink, or a valve is stuck, don’t force it — you can snap an old valve and turn a small job into a flood. Instead, shut off the main water supply to the house, usually where the water line enters the home: in the basement, utility room, garage, or outside near the water meter. Then open the faucet to drain the lines.
Step 2: Take the Handle Off and Pull the Old Part
The pattern is the same for all four faucet types:
- Find the handle screw. It’s usually hidden under a small decorative cap on top of the handle, or under a red/blue hot/cold button. Pop the cap off with a flathead screwdriver.
- Remove the handle. Unscrew the handle screw (Phillips or Allen) and lift the handle off. If it’s stuck, wiggle it gently — never yank it.
- Remove the retaining nut or clip. Under the handle you’ll find a bonnet nut (unscrew it with your adjustable wrench) or a small metal retaining clip (pull it out with needle-nose pliers). For cartridge faucets, the cartridge sits directly underneath.
- Pull the part out and photograph it. Note which way it was facing — for cartridges, hot/cold orientation matters. Check the brand name on the faucet (Moen, Delta, Kohler, or Pfister are the most common): cartridges are brand-specific and not interchangeable.
If you’re still building your toolkit, our guide to The 12 Tools Every First-Time Homeowner in the US Should Own (and What to Skip) covers the adjustable wrench, pliers, and screwdrivers you’ll reach for here — and what you can skip buying.
Step 3: Fix a Cartridge Faucet (Most Common)
Cartridge faucets are the most common type in modern US homes, so this is the fix most readers will need.
- With the handle and retaining clip or nut removed, pull the old cartridge straight up. If it’s stuck, wiggle it gently side to side.
- Take the old cartridge to the store and match it exactly. Common replacements: a Moen 1224 two-handle cartridge runs about $15.15 at Home Depot, a Moen 1225 single-handle cartridge about $12.47, a Delta RP19804 single-handle cartridge about $25–$32, and a Kohler GP500520 about $30–$40. Generic replacements cost a few dollars less but don’t always fit — the genuine part is usually worth the small premium.
- Coat the new cartridge’s O-rings with a dab of plumber’s silicone grease (about $5 for a small tube at Home Depot).
- Slide the new cartridge in, facing the same direction as the old one. Replace the retaining clip or nut, reattach the handle, and tighten the handle screw.
- Turn the water back on slowly at the angle stops, then test the faucet. Run it for a few seconds, turn it off, and watch the spout for a full minute. No drip means you’re done.
Step 4: Fix a Compression Faucet (Two-Handle, Older Homes)
Compression faucets are the simplest fix of all — the culprit is almost always a flat rubber washer at the bottom of the stem.
- After removing the handle, unscrew the packing nut with your adjustable wrench and pull the stem straight out.
- At the bottom of the stem you’ll find a rubber washer held on by a small brass screw. Unscrew it and pry the old washer off.
- Take the old washer to the store to match the size exactly. A washer assortment kit runs about $8–$12 at Home Depot and covers most sizes, and a generic variety pack can be as little as $4–$6. Buy the assortment, not a single washer — the leftovers cost almost nothing and you’ll use them on the next faucet.
- Press the new washer into place, screw it down, and coat the stem’s O-ring with silicone grease before sliding it back in. Reassemble, turn the water back on, and check for drips.
If it still drips after a new washer: the valve seat — the brass surface the washer presses against — may be pitted or grooved. A seat wrench (about $10) can smooth a mildly worn seat in a few minutes. If the seat is badly corroded, that’s a job for a plumber.
Step 5: Fix a Ball Faucet (Single-Handle Delta)
Ball faucets have more small parts, but the repair is still very doable:
- Remove the handle, then unscrew the dome-shaped cap on top (by hand, or with adjustable pliers wrapped in a rag to protect the chrome).
- Lift out the ball, the cam, and the two rubber seats and springs underneath. The seats and springs are the parts that wear out — replace all of them as a set while you’re in there.
- A Delta RP4993 seats and springs repair kit costs about $7.98 at Home Depot, and the Danco equivalent (model 86968) runs about $6.48. A full Delta ball repair kit with a new ball, cam, seats, and springs runs about $15–$20.
- Drop the new springs in first, then the seats on top, then the ball, cam, and cap. Reattach the handle, turn the water on, and test. If the handle feels stiff, loosen the adjusting ring inside the cap a quarter-turn.
Step 6: Fix a Ceramic Disc Faucet (Brief)
Ceramic disc faucets rarely leak, and when they do, the fix is usually cleaning or a cartridge swap. Remove the handle and the escutcheon (the decorative cover), then unscrew the cylinder holding the ceramic discs. Lift out the disc cartridge: if the discs are coated in white mineral deposits, soak them in white vinegar for 30 minutes and scrub gently with an old toothbrush. If a disc is cracked or chipped, the cartridge needs replacing. Replacements are brand-specific and run roughly $15–$40, so take the old one to the store to match it. Reassemble with a light coat of silicone grease on the seals, turn the water on, and test.
Tools You’ll Need
- Adjustable wrench — for packing nuts, bonnet nuts, and supply lines
- Phillips and flathead screwdrivers — for handle screws and decorative caps
- Needle-nose pliers — for retaining clips and small parts
- Allen wrench set — many modern handles use a small hex screw
- Plumber’s silicone grease — about $5; coat every O-ring before reassembly
- Towel or rag — to plug the drain and mop up water from the lines
Parts and Costs
| Part | Faucet type | Typical price |
|---|---|---|
| Moen 1224 cartridge (2-handle) | Cartridge | ~$15.15 at Home Depot |
| Moen 1225 cartridge (single-handle) | Cartridge | ~$12.47 at Home Depot |
| Delta RP19804 cartridge | Cartridge | ~$25–$32 |
| Kohler GP500520 cartridge | Cartridge | ~$30–$40 |
| Delta RP4993 seats & springs kit | Ball | ~$7.98 at Home Depot |
| Danco 86968 seats & springs kit | Ball | ~$6.48 at Home Depot |
| Faucet washer assortment kit | Compression | ~$8–$12 |
| Generic washer variety pack | Compression | ~$4–$6 |
| Plumber’s silicone grease | All types | ~$5 |
| Seat wrench (if the valve seat is pitted) | Compression | ~$10 |
Total DIY cost for most repairs: $5–$25 in parts. A professional faucet repair typically runs $100–$300 in 2026 — the national average is about $180, including a $50–$150 service call fee plus labor at $75–$200 an hour. Even at the low end, the plumber’s visit costs five to ten times the parts.
When to Call a Plumber
Most dripping faucets are a beginner DIY job. But there are situations where the smart move is to put the wrench down and call a licensed plumber:
- The shutoff valves are the problem. If an angle stop under the sink is corroded, seized, or leaking — or the main shutoff won’t close or you can’t find it — stop. You have no safe way to work on the faucet, and replacing a shutoff means working on a live supply line.
- The leak is behind the wall or under the floor. Water stains on the ceiling below, a damp wall, or a leak you can hear but can’t see all point to a pipe problem, not a faucet problem. Hidden leaks can run $300–$600 or more once access and drywall repair are included.
- The faucet or valve body is cracked, or the threads are stripped. A cracked body can’t be sealed, and forcing a stripped thread only makes it worse. At that point you’re replacing the faucet, and a pro can do it in an hour or two.
- You replaced the right part and it still drips. A persistent drip after a new cartridge or washer usually means a damaged valve seat, a cracked body, or a problem further up the line. You’ve already saved the diagnostic fee by ruling out the easy fix — let a pro take it from there.
- Your home has galvanized steel or very old plumbing. Old pipes can be brittle, and disturbing one fitting can crack the next. If your pipes look heavily corroded, get a plumber’s eyes on the job before you start.
A good rule of thumb: if at any point you feel like you’re forcing something, stop. Forcing a stuck nut, a seized valve, or a jammed cartridge is how a $15 repair becomes a $300 emergency call.
Safety Note
- Shut the water off before you touch anything. With the angle stops closed — or the main shutoff closed if the stops don’t work — there is no pressure behind the parts you’re removing.
- Know where your main shutoff is before you need it. Find it today, while nothing is leaking, and test that it turns. If it’s stuck, that’s a small job for a plumber now and a crisis later.
- Keep water off cabinets and floors. Lay a towel under the sink and mop up drained water right away — standing water warps particle-board cabinets and subfloors fast.
- Don’t force anything. A nut that won’t budge with a normal wrench is telling you something — usually corrosion. Penetrating oil and patience beat a longer lever.
Conclusion
A leaky faucet is one of the best first plumbing projects a new homeowner can take on. The diagnosis takes two minutes, the parts cost less than a takeout dinner, and the whole job fits comfortably inside an hour — including the trip to Home Depot. You’ll save $100 or more over a plumber’s visit and stop wasting thousands of gallons of water a year.
So next time you hear that drip, don’t just tighten the handle harder — that only wears the washer out faster. Shut off the water, pull the old part, match it at the store, and swap it in. Your water bill (and your sleep) will thank you.
Sources
Prices and facts in this article were verified against the sources below in November 2026. Prices are US retail prices at the time of checking and vary by store and region.
- Home Depot — Moen 1224 2-Handle Replacement Cartridge, $15.15 — homedepot.com
- Home Depot — Danco 6S-1H/C Stem for Moen (replaces Moen 1224), $13.98 — homedepot.com
- Home Depot — Danco 2 in. Cartridge for Moen Duralast Faucets (replaces Moen 1255), $20.48 — homedepot.com
- Home Depot — Delta Universal Seats and Springs Repair Kit RP4993, $7.98 — homedepot.com
- Home Depot — Danco Seats and Springs Kit for Delta Faucets 86968 (replaces Delta RP4993), $6.48 — homedepot.com
- FixItWhy — “Why Your Faucet Keeps Dripping” (June 15, 2026) — fixitwhy.com
- What’s The Process For — “How to Fix a Leaky Faucet” — whatstheprocessfor.com
- HomeBraces — “How to Fix a Leaky Faucet Without Calling a Plumber” — homebraces.com
- ABS Pipes — “Faucet Repair Cost: Drips & Leaks (2026)” (updated October 26, 2026) — ABSpipes.com
- HomeworthHQ — “Plumbing Repair Cost (2026)” — homeworthhq.com
- Thumbtack — “2026 Sink & Faucet Repair Cost Guide” — thumbtack.com
- DIY Mastery Guide — “How to Fix a Leaky Faucet” (September 18, 2026) — diymasteryguide.com
- Homeowner Basics — “Leaky Faucet? How to Fix a Dripping Faucet by Type” (updated October 3, 2026) — homeownerbasics.com
- MySibey — “How to Fix a Leaky Faucet” — mysibey.com
Comments
Post a Comment